oONsbRizzOo Tutorial


Tools and equipment used :

Custom Switch (controls fan speed)
- soldering iron kit (comes with solder) - $10
- push on/off switch - $3
- soldering flux - $5
- wire - (idk i found it around my house lol probally like $5 at radioshack)
- knife/ stripping tool - $10
- power drill
- drilling drill bits

Painting Tools
- Tiger striped paint mask -$5
- montana acrylic spray paint - $10 (per can)
- painters tape - $1


Custom Switch (controls fan speed) Tutorial

First :
Make sure you have all the tools needed

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]

Second :
Open up your xbox and figure out where your fan is; then disconnect it; then roll back the electrical tape and find the blue wire; cut the blue wire in the the middle.

[ Register or Signin to view external links. ]

Third :
Get your wire and cut two wires about 6 inches long each; get your knife or stripping tool and strip about half an inch off both the ends of the wire

[ Register or Signin to view external links. ]

Fourth :
Get your on/off switch and twist the ends of the wire to the connectors of the switch.
Then get your solder flux and lube up the connection you just made with the wire and switch then get your soldering iron and solder the connection together

[ Register or Signin to view external links. ]

Fifth :
Get your knife and strip the ends of the blue wire. Then twist the other end of the switch wires to the ends of the blue wire. Apply soldering Flux; then solder the connection together.

[ Register or Signin to view external links. ]

Sixth :
Grab your Drill and drilling drill bit (the drillbit should be the same diameter of the stwitch) and drill a hole into the metal housing of the Xbox 360. The hole should be above the HDMI / A/V connection. Make sure the switch fits properly. After the hole is made grab the plastic cover that goes over the HDMI / A/V connection and line it up to where it would normally fit on the xbox and drill a hole in the same spot you made a hole in the metal housing.

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]

Seventh :
Put the switch in and reassemble the Xbox. There you have it

[ Register or Signin to view external links. ]

Painting Tutorial

First :
Completely disassemble your Xbox 360; make sure you Top vent, bottom vent (including the HDD cover, Left side panel, right side panel, Front face plate (whatever its called) , the back piece for the hdmi/av connection etc. and the DVD drive cover piece thing.

Second :
Tape up what you don't want painted, whether that be rubber parts , the power on button on the faceplate , or stuff you want a different color. we are going to start off with the base a color of green because i want my tiger stripes green. Once every thing is taped up go ahead and spray paint it.

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]

Third :
lets say you want your usb hub and the dvd drive on the faceplate to be silver stripes instead of green , All you would have to do is spray paint just those parts silver then put painters tape on those part then spray paint the rest of the face plate green then remove the usb hubs and dvd drives painters tape.

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]

Fourth :
Once you have all the base colors you want go ahead and apply the tiger stripes the way you want them on the console

[ Register or Signin to view external links. ]

Fifth :
if you were one of those people who wanted the dvd drive and usb hub to be a different color you would reapply painters tape over those parts (reapply the tape over the tiger stripes) once thats done spray paint your console with your primary color mine is silver. once it dries give it a second coat.

Sixth :
after your console is dried with a second coat go ahead and take the tape off the dvd drive cover and usb hub cover and cover everything else around it with tape. once everything is covered up with tape go ahead and spray paint those parts what ever your base color was mine was green. let it dry and give it a second coat.


seventh :
once everything is dried remove all the tape including the tiger stripes very carefully . Then spray paint the xbox with some clear coat (i prefer a matte finish) once that dries enjoy your sexy 4ss 360

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]


heres another xbox i did for my friend , he drew me a diagram on paint lmfaoo on how he wanted it and i did it

[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]

And if you want to flash your xbox follow this tutorial; basically showing you how to revert it to stock pcb but if you have common sense you could follow this backwards and figure out how your suppose to install the blank pcb board onto your 360

[ Register or Signin to view external links. ]