You are viewing our Forum Archives. To view or take place in current topics click here.
How To RGH Corona V2 4gb 16202 With DGX TUTORIAL
Posted:
How To RGH Corona V2 4gb 16202 With DGX TUTORIALPosted:
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Tutorial For RGHing DGX Corona V2 4gb 16202
Required Equipment :
Xecuter CoolRunner QSB Slim v3 Corona: NEEDED [ Register or Signin to view external links. ]
Xecuter DGX v1.0S Slim TX: Needed [ Register or Signin to view external links. ]
Xecuter Corona v2 4GB NAND RW Kit : Needed [ Register or Signin to view external links. ]
Xecuter CoolRunner v3 Lite CR3: Needed [ Register or Signin to view external links. ]
Xecuter CoolRunner QSB V3 Comms USB Cable: Needed [ Register or Signin to view external links. ]
Xecuter J-R Programmer: Needed or NandX [ Register or Signin to view external links. ]
For this Tutorial You WILL NEED the Xecuter CoolRunner QSB Slim v3 Corona
Install The Xecuter Corona v2 4GB NAND RW Kit and plug it in to your computer.
Should look like this Afterwords
[ Register or Signin to view external links. ]
We can start using the latest version of J-Runner software and reading the nand as usual twice or more.
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
Now we have our nand backup.
[ Register or Signin to view external links. ]
We can now flash the modified ECC that TX has released Go To the Advanced Tab At the Top The Press Write DGX:
[ Register or Signin to view external links. ]
A Pop up Will Apeare Select Yes
[ Register or Signin to view external links. ]
Another Pop Up Will Apeare Select Corona 4GB and Then Ok
[ Register or Signin to view external links. ]
Another Window Will Pop up The Same One We used to Read The Nand
[ Register or Signin to view external links. ]
Find The Read/Write kit select it Then Press Write
At this point we can install the DGX chip. The points are all the same as other glitch chips with the exception of power source 5V instead 3,3V, it's advisable to use thicker cable then AWG30 for better timing.
Here's a picture of new top product from TX team:
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
We are going now to show how to connect DGX to the motherboard: The Switches must Be set like this 1-7 OFF 8 ON For Corona
[ Register or Signin to view external links. ]
Once the DGX is installed Grab the Xecuter CoolRunner QSB V3 Comms USB Cable Go on to J-Runner And Select Moniter Comm
[ Register or Signin to view external links. ]
Then Press Open Port
[ Register or Signin to view external links. ]
After that Boot the Xbox
and The CPU Key should Load on the Comm Moniter
retrieve it and put it in the Cpu Key Box
after that Find The NandDump.bin and create a Glitch Image
Make Sure In XeBuild options at the right You select RGH2 and What Dashboared Version You Are on.
[ Register or Signin to view external links. ]
After that Make Sure The Xecuter Corona v2 4GB NAND RW Kit is connected then Write the Nand You Just Created To That.
Next Flash The CR3 Lite
Cr3lite setup
Lk1 open
Lk2 short
Lk3 open
Lk4 all open
S2 dip switch 6 on
S4 dip switch 4 on (you can try with your own combo on both dip to get better result)
Timing file 3_2 / 3_3 ( 3_2 suggested it give me best result)
Range booting time 5-30sec to boot
Then Install It
[ Register or Signin to view external links. ]
Cpu_rst point
i used ft3ft10 for my cpu reset point...shortened it and make it 14cm
Take yellow wire from phat wire pack and make it short and up to length to the point.
if you are not familiar witch TX coolrunner naming:
C- Post
D- CPU RESET
E- SCL
F SDA
GND - Ground
Required Equipment :
Xecuter CoolRunner QSB Slim v3 Corona: NEEDED [ Register or Signin to view external links. ]
Xecuter DGX v1.0S Slim TX: Needed [ Register or Signin to view external links. ]
Xecuter Corona v2 4GB NAND RW Kit : Needed [ Register or Signin to view external links. ]
Xecuter CoolRunner v3 Lite CR3: Needed [ Register or Signin to view external links. ]
Xecuter CoolRunner QSB V3 Comms USB Cable: Needed [ Register or Signin to view external links. ]
Xecuter J-R Programmer: Needed or NandX [ Register or Signin to view external links. ]
For this Tutorial You WILL NEED the Xecuter CoolRunner QSB Slim v3 Corona
Install The Xecuter Corona v2 4GB NAND RW Kit and plug it in to your computer.
Should look like this Afterwords
[ Register or Signin to view external links. ]
We can start using the latest version of J-Runner software and reading the nand as usual twice or more.
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
Now we have our nand backup.
[ Register or Signin to view external links. ]
We can now flash the modified ECC that TX has released Go To the Advanced Tab At the Top The Press Write DGX:
[ Register or Signin to view external links. ]
A Pop up Will Apeare Select Yes
[ Register or Signin to view external links. ]
Another Pop Up Will Apeare Select Corona 4GB and Then Ok
[ Register or Signin to view external links. ]
Another Window Will Pop up The Same One We used to Read The Nand
[ Register or Signin to view external links. ]
Find The Read/Write kit select it Then Press Write
At this point we can install the DGX chip. The points are all the same as other glitch chips with the exception of power source 5V instead 3,3V, it's advisable to use thicker cable then AWG30 for better timing.
Here's a picture of new top product from TX team:
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
We are going now to show how to connect DGX to the motherboard: The Switches must Be set like this 1-7 OFF 8 ON For Corona
[ Register or Signin to view external links. ]
Once the DGX is installed Grab the Xecuter CoolRunner QSB V3 Comms USB Cable Go on to J-Runner And Select Moniter Comm
[ Register or Signin to view external links. ]
Then Press Open Port
[ Register or Signin to view external links. ]
After that Boot the Xbox
and The CPU Key should Load on the Comm Moniter
retrieve it and put it in the Cpu Key Box
after that Find The NandDump.bin and create a Glitch Image
Make Sure In XeBuild options at the right You select RGH2 and What Dashboared Version You Are on.
[ Register or Signin to view external links. ]
After that Make Sure The Xecuter Corona v2 4GB NAND RW Kit is connected then Write the Nand You Just Created To That.
Next Flash The CR3 Lite
Cr3lite setup
Lk1 open
Lk2 short
Lk3 open
Lk4 all open
S2 dip switch 6 on
S4 dip switch 4 on (you can try with your own combo on both dip to get better result)
Timing file 3_2 / 3_3 ( 3_2 suggested it give me best result)
Range booting time 5-30sec to boot
Then Install It
[ Register or Signin to view external links. ]
Cpu_rst point
i used ft3ft10 for my cpu reset point...shortened it and make it 14cm
Take yellow wire from phat wire pack and make it short and up to length to the point.
if you are not familiar witch TX coolrunner naming:
C- Post
D- CPU RESET
E- SCL
F SDA
GND - Ground
Last edited by Mods4Dworld ; edited 14 times in total
The following 3 users thanked Mods4Dworld for this useful post:
#2. Posted:
Status: Offline
Joined: Aug 01, 201014Year Member
Posts: 3,245
Reputation Power: 148
Status: Offline
Joined: Aug 01, 201014Year Member
Posts: 3,245
Reputation Power: 148
Once you unsolder the DGX and have your cpu key, you just make a nand dump, create a freeboot image, wire up the glitch chip like normal and voila.
Or at least that's my understanding.. Don't see how anything could be different.
Or at least that's my understanding.. Don't see how anything could be different.
- 1useful
- 0not useful
#3. Posted:
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Trinity Dip #8 OFF
Corona Dip #8 ON
1-7 Always off. (down posistion)
Corona Dip #8 ON
1-7 Always off. (down posistion)
- 0useful
- 0not useful
#4. Posted:
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Now A Complete Tutorial
- 0useful
- 0not useful
#5. Posted:
Status: Offline
Joined: Mar 07, 201113Year Member
Posts: 4
Reputation Power: 0
Status: Offline
Joined: Mar 07, 201113Year Member
Posts: 4
Reputation Power: 0
hi i have been trying to do this for hours now. It wont let me build my ECC image. I am on the latest dash "16202" and i have the 9231 CB. I have made 4 matching nand dumps from my console and when I load one and select create ECC it tells me this
XOR HACK NEEDED FOR CB 9231
File C:\Users\i5\Documents\Xbox Modding\RGH\J-Runner\J-Runner v02 (278) Core Pack\common\CB\CB_B.9231.bin not found!
Failed to open CB_B.9231.bin
I dont understand what is wrong I am using the latest version of J-Runner (284). Please reply back to me as soon as possible thanks! P.S. I have a Trinity
XOR HACK NEEDED FOR CB 9231
File C:\Users\i5\Documents\Xbox Modding\RGH\J-Runner\J-Runner v02 (278) Core Pack\common\CB\CB_B.9231.bin not found!
Failed to open CB_B.9231.bin
I dont understand what is wrong I am using the latest version of J-Runner (284). Please reply back to me as soon as possible thanks! P.S. I have a Trinity
- 0useful
- 0not useful
#6. Posted:
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
You dont build a ecc off of your nand.
You just write the DGXECC/ Go to advanced write DGX. I suggest you follow the guide on Xecuters forum like they ask.
and use 14cm wire.... keep cold booting it until it boots
You just write the DGXECC/ Go to advanced write DGX. I suggest you follow the guide on Xecuters forum like they ask.
and use 14cm wire.... keep cold booting it until it boots
- 0useful
- 0not useful
#7. Posted:
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
stevenshdcinema wrote hi i have been trying to do this for hours now. It wont let me build my ECC image. I am on the latest dash "16202" and i have the 9231 CB. I have made 4 matching nand dumps from my console and when I load one and select create ECC it tells me this
XOR HACK NEEDED FOR CB 9231
File C:\Users\i5\Documents\Xbox Modding\RGH\J-Runner\J-Runner v02 (278) Core Pack\common\CB\CB_B.9231.bin not found!
Failed to open CB_B.9231.bin
I dont understand what is wrong I am using the latest version of J-Runner (284). Please reply back to me as soon as possible thanks! P.S. I have a Trinity
Yes what Mafia said you don't Create a ECC from your Nand Dump But i highly Recommend This new ECC Xecuter Has Released For Corona v2's and v4's Load it in jrunners Source Box and press Write ECC. dl. dropbox .com/u/33453664/CORONA_4GB_DGXv2.ecc the link i have provided has alot of bugg fixes but if you would like to go with the more standard way in Jrunner at the top Click the Advanced Button and Press Write DGX as Mafia Said
- 0useful
- 0not useful
#8. Posted:
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Status: Offline
Joined: Aug 03, 201212Year Member
Posts: 140
Reputation Power: 5
Please Thank the post if this helped you in anyway.
- 0useful
- 0not useful
#9. Posted:
Status: Offline
Joined: Oct 31, 201212Year Member
Posts: 1
Reputation Power: 0
can i install the dgx without tx corona v3 QSB ?
- 0useful
- 0not useful
#10. Posted:
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
AranHiwa wrote can i install the dgx without tx corona v3 QSB ?
DGX is standalone glitch chip. You use it get your key on 15574+ slims, after you get your cpu, then you remove it and install coolrunner for permenant install.
You can use it with the QSB, follow the install guide.
- 2useful
- 0not useful
You are viewing our Forum Archives. To view or take place in current topics click here.