You are viewing our Forum Archives. To view or take place in current topics click here.
just lifted the pad on r2p12
Posted:

just lifted the pad on r2p12Posted:

TTG_KillerKUSHY
  • Challenger
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
i was trying to jtag a falcon with a ruined db1f1 and the other alt that starts with fu so i used boxxdrs jtag method and i didn't relise the pad on r2p12 was so delicate its gone. I got a lil ball of solder to stick but the xbox doesn't power on at all if it is completely gone it'll just be my pratice board or ill just strip the box of everything useful i can still read/write nand to it play nd charge gets power from it but the xbox is completely dead at the moment anyone ever do this i was told not to lift the pad and i know it sucks that i did and its probally not going to work again but damn :/
#2. Posted:
maveriik14
  • Ladder Climber
Status: Offline
Joined: Sep 20, 201014Year Member
Posts: 313
Reputation Power: 40
Status: Offline
Joined: Sep 20, 201014Year Member
Posts: 313
Reputation Power: 40
all three gone?? man, haha id say you need a little soldering practice lol. but you lifted the pads on all three? if you did, i dont know of any other points, you could extract the kv from that one and use it on a jtag later...
#3. Posted:
xLasers
  • TTG Contender
Status: Offline
Joined: Aug 06, 201014Year Member
Posts: 3,068
Reputation Power: 141
Status: Offline
Joined: Aug 06, 201014Year Member
Posts: 3,068
Reputation Power: 141
You can try soldering to the wires that come into the point, or take the screws off the bottom and look under the motherboard where you soldered and try to clean it up, you never know it may power back on if there is a cold joint, splatter, etc. I had a jtag do this to me before
#4. Posted:
TTG_KillerKUSHY
  • Challenger
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
fixed it when i screwed up r2p12 i blew 2 10k ohm resistors took them off cleaned the points nd put new ones on and green lights are back last time i use a .7mm tip on a Tiny tiny tiny little solder point like that.
#5. Posted:
iSmeXy
  • TTG Senior
Status: Offline
Joined: Jul 04, 201014Year Member
Posts: 1,402
Reputation Power: 70
Status: Offline
Joined: Jul 04, 201014Year Member
Posts: 1,402
Reputation Power: 70
TTG_KillerKUSHY wrote fixed it when i screwed up r2p12 i blew 2 10k ohm resistors took them off cleaned the points nd put new ones on and green lights are back last time i use a .7mm tip on a Tiny tiny tiny little solder point like that.


nice job, and like the avatar.,
#6. Posted:
TTG_KillerKUSHY
  • Challenger
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
Status: Offline
Joined: Aug 28, 201014Year Member
Posts: 171
Reputation Power: 5
haha thanks 8)

20 charactersss
Jump to:
You are viewing our Forum Archives. To view or take place in current topics click here.