Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Dental wrote try reflashing it with the nand on the disk then update it

Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?

im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756

flash that 16756 image back to the console and make sure that it is able to get to dash

ok just did its on 16756 now

Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.

ok says there the same so how do i make a new nand from j runner is it by just updating it?

Make sure the correct dash is selected in the upper right, as well as the correct mod type (jtag/rgh1/rgh2) then click the giant button that says "create xebuild image"...

allright.do i put the dash that the nand is on which is 16756 or 16767 just wanna make sure

The target dash...

20202020202020202020202002

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Dental wrote try reflashing it with the nand on the disk then update it

Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?

im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756

flash that 16756 image back to the console and make sure that it is able to get to dash

ok just did its on 16756 now

Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.

ok says there the same so how do i make a new nand from j runner is it by just updating it?

Make sure the correct dash is selected in the upper right, as well as the correct mod type (jtag/rgh1/rgh2) then click the giant button that says "create xebuild image"...

allright.do i put the dash that the nand is on which is 16756 or 16767 just wanna make sure

The target dash...

20202020202020202020202002

it dosent let me click jtag when i have 16767 selected for the dash but it does when i have 16756 selected ???

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Doink wrote

TheWeekendModder wrote

Dental wrote try reflashing it with the nand on the disk then update it

Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?

im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756

flash that 16756 image back to the console and make sure that it is able to get to dash

ok just did its on 16756 now

Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.

ok says there the same so how do i make a new nand from j runner is it by just updating it?

Make sure the correct dash is selected in the upper right, as well as the correct mod type (jtag/rgh1/rgh2) then click the giant button that says "create xebuild image"...

allright.do i put the dash that the nand is on which is 16756 or 16767 just wanna make sure

The target dash...

20202020202020202020202002

it dosent let me click jtag when i have 16767 selected for the dash but it does when i have 16756 selected ???

i got jr good just now its saying inis missing