skatertg wrote If your coming on this thread to ask where to buy a JTAG from then i suggest these sites to keep you from spamming this post:

www.thetechgame.org

www.ebay.com

Or Check out xenonjtags or KoDeMan's post

If people have other sites then PM me them and i will put them on here.

---

Installing XeXMenu

Click to View Content

This first part of the tutorial is how to install XeXMenu the quick and easy way.

Things you will need:

A transfer Cable

This file: [ Register or Signin to view external links. ]

To do this it is very simple; simply copy the CODE9999 Folder into Partition3 > content > 0000000000

A VERY short video of how to do it on PC:

Go onto Jtag and XeXMenu should be there under recent games in the game library. Or to find it quickly just hit the middle button on xbox controller and go to Quick Launch, and it'll either be under Recent or Latest Downloads.

Another way you could install XeXMenu is by putting the CODE9999 file onto a disk (either a CD-R or a DVD-R, CD-R worked for me so maybe use that)

Things You will need:

A DVD-R/CD-R

This file: [ Register or Signin to view external links. ] (CODE9999 File again)

Okay to do this, it is also simple. Burn file to the disk then insert the disk into your JTAG. Then you use the directory on XeXMenu to find the DVD and copy the CODE9999 that is on the DVD into Partition3 > content > 0000000000 just like the first way.

The go onto the Jtag and XeXMenu should be there under recent games in the game library. Or to find it quickly just hit the middle button on xbox controller and go to Quick Launch, and it'll either be under Recent or Latest Downloads”.

These are buttons that you can use in XeXMenu & what they do:

[ Register or Signin to view external links. ]

_____________________________________________________________________________________

How to Copy a game into XeXMenu

Click to View Content

Okay so now you have XeXMenu installed next you are going to want to install your copy of Modern Warfare 1 or 2 onto the JTAG, make sure the hard drive your using has enough memory for 6-7gb of data. Follow this video on how to do it, I already have MW1 & 2 installed onto my hard drive so i am going to show you with a different game but it's the same way of doing it.

Here is the video tutorial put into 2 parts; i will do a written one after:

Part 1:

[ Register or Signin to view external links. ]

Part2:

Alright, so now you have seen the video. If you didn't see on the video to find out what buttons to press to do things press back on your controller. The (Y) button is the button to get that mini menu up where you can copy and paste, create new folders etc, RB and LB switch menus so to go to your hard drive like i did you press once on RB.

When you are going to rip your game onto your HDD, great a Folder called:

Games > [then a folder of whatever the game is called]

Then Press (Y) to bring up the menu once you’re in the folder of the game you want to copy

And go down to CopyDVD

Then press A

It'll then come up with that warning sign, insert the disk into the disk tray and close it

Then wait around 10 seconds so you know the disk has loaded THEN press Confirm

It'll then start copying the game like it shows, but make sure your controller doesn’t disconnect if you go away and leave it. I let mine disconnect once and it stopped copying the game.

_____________________________________________________________________________________

How to put the files onto XeXMenu needed to create the lobbies

Click to View Content

To put your files onto your JTAG, you will need 3 files for MW & MW2 Lobbies. (via XeXMenu)

Here are the files for MW1:

System Link: [ Register or Signin to view external links. ] it may work online, i haven't checked before.

And here are the files for MW2:

[ Register or Signin to view external links. ]

Here is a video on how to copy the files over:

http://tinypic.com/usermedia.php?uo=JDduC2mKjds%2BWTIe/UVg7Yh4l5k2TGxc

So basically, put the files on a USB pen drive & stick the USB into your JTAG. Then you have to Load up XeXMenu. After you have loaded up XeXMenu press ‘RB’ to go across to where the HDD is etc, the USB should pop up straight away like it did in the video. If it did not then simply keep pressing right or left on the D-PAD until you find it.

Once you have found the USB hover over the files you want to copy and press (Y) to make the Menu appear. Go down to Copy or Cut, your choice and press (A), then keep pressing the D-PAD left or right until you find your hard drive. Find your ‘Games’ Folder, go into it, then go into where your keeping MW1 or MW2 and simply paste the files in. To paste Just hit (Y) and go down to Paste and click (A). You can only Copy/Cut and Paste 1 File at a time, and if it says do you want to overwrite this file just hit Yes.

Okay next is how to put the files on your xbox using a transfer cable... I know TTG_Zac already made this but not with a video tutorial so yeah, I'm remaking there tutorial so here.

Okay so basically follow what I do in the video, if you don't get what I have done there will be a written tutorial underneath it.

Okay so, basically all you have to do is, extract the .rar files which I have included above for the MW1/MW2 lobbies, have the .iso on the Hard drive ready then go and open your HDD in Xport360/Xplorer360 open where you have saved the Games, that's why I suggested making a Game Folder because it'll make it easier for you to find etc, but when you open up the folder where the Game was ripped to simply drag and drop the files into it.. Its as simple as that.

Here is a Link to Zacs Picture/text tutorial on putting files on via transfer cable:

https://www.thetechgame.com/Forums/viewtopic/t=73144.html

I hope this has helped you.
This is all my OWN work so Credits go to Skatertg

---

PART 2 OF TUT

How to Install a few Emulators (snes360 etc)

Installing Snes360 via transfer cable

Click to View Content

DOWNLOAD ROMS HERE: [ Register or Signin to view external links. ]

HERE IS SUPER MARIO! -> [ Register or Signin to view external links. ]

You will need these files:

This one will work on freeboot & XBR2: http://www.megaupload.com/?d=NEWMJ39N

This will work on XBR2 & XBR3: http://www.megaupload.com/?d=V5CZJ33D

Okay here is another quick video tutorial:

So yeah, if that didn't explain it here is a short and simple written tut for you:

Just extract the .rar file, grab the FFED0707 folder and just drag and drop it into Partition 3 > Content > 000000000000000.

Then next you will need to make this folder and sub-folders in this order; Emus > Snes360 > Roms. Then put the Roms for the snes games into the Roms sub folder. Then drag the folder into your partition 3 (where it says Cache, Content etc) and leave it there.

How to install snes360 via USB pen drive:

Using the files I have given you above put them on a USB pen drive, open the USB drive in XeXMenu & copy the FFED0707 Folder straight into the content > 000000000000. If you are going to do it this way, make sure that you have pre-made the Emus > Snes360 > Roms folder/sub-folders because it'll save you sometime.

---

How to Install FreeStyle Dashboard

Click to View Content

Okayyy, so as requested by TTG_JAMBO I have made a tutorial on how to install freestyle dashboard.
You will need these files:
Freestyle dashboard:

[ Register or Signin to view external links. ]

To change your USB Pen Drive into FAT32:

[ Register or Signin to view external links. ]

How to put the freestyle dashboard onto your USB:

How to install Freestyle dashboard onto your xbox & so it comes up on your Full Games.

Part 1:

Sorry, there is no second video tut part… it keeps failing to upload ALL the time on any upload video site I have used, can someone suggest a upload website where I can upload the second video tut onto?

For now you will have to make do with the written tutorial I suppose.

Written tut:

Okay so you need to make your portable HDD/USB pen drive into a FAT32 format. They should be that already by default but if not use the program I provided to change it. It’s pretty simple to change the format using this program, simply open the program chose the drive and hit format & wait for it to be finished.

Next, copy the freestyle dashboard onto your USB pen drive. But only copy these folders:

- FreeStyle
- FSD Indexer
- Launch
- Source

Like it was shown in the video basically.

Next put the USB pen drive into the BACK USB slot (Next to the Ethernet cable port).

Then you are going to want to go into XeXMenu and go to your USB.

Go into the Launch folder and copy the freestyle-usb file (NOT the .iso version).

Then go to your HDD > Content > 000000000000000> C0DE9999

Now go into the C0DE9999 folder, and then CREATE a new Folder EXACTLY called this: 00007000

Copy the freestyle-usb file (AGAIN NOT THE .ISO ONE!) into the 00007000 folder

Then go back to dashboard, go to Game Library > FULL GAMES & you should see Freestyle Dash 1.09

Simply click on it and it'll run. HOWEVER! If you take out the USB/external HDD and try to run it, freestyle dash will not load.

So I guess you could try putting the file for freestyle dash on the root of your HDD (where you see the content, cache etc) then put the freestyle-usb file into the 00007000 again ¦ if you do try this let me know if it works, I would test it myself but im a bit too busy to at the moment.

---

How to rebuild your NAND to upgrade to Freeboot [If you do not have original Nand] Only for people who actually know what they are doing..

Click to View Content

Okay to start off with, I am going to be very busy in the next 2weeks, college work etc so if you do need help with this please be patient and I will try to get to you asap


Basically you can rebuild a NAND to its original state. This will be especially useful for those who do not have their original NAND and want to upgrade from XBR3 to freeboot & also if you do not know how to do this you really shouldn't have a JTAG... just my opinion haha. My friend has tested this and it worked for a Falcon board.



Things you need:
Flash360. -> [ Register or Signin to view external links. ]

Your CPU key (the one you get from Xell or Xellous not the donor's key).

To find your CPU KEY:

Have a camera ready to take a picture of the Fuse Set's that pop up briefly.
Take a picture that includes fuse set 3,4,5,and 6. These contain your CPU key.

[ Register or Signin to view external links. ]

Take either 3 and 5 or 4 and 6. This will make up your cpu key. 3=4 5=6 So for example. I will take 3 and 5.

3= E42D681ED06A6D1C

5= 1FFD8E48C56A2058


So my CPU Key is - E42D681ED06A6D1C1FFD8E48C56A2058


Adding either one of the two will make your CPU key.


After getting your cpu key you can write your original nand image back to the board. Or go straight forward and install XBReboot or freeBOOT.
^ copy and pasted part.

• A NAND that matches your motherboard type with the 7371 kernel. You don't need their CPU key, any encrypted nand image will do.

• 360 Flash Tool download -> [url] [ Register or Signin to view external links. ]


Instructions:

• Launch Flash360 and use it to dump your NAND.

Extract the kv.bin and config.bin with Nandpro2b with the following commands:

nandpro.exe flashdmp.bin: -r16 rawkv.bin 1 1

nandpro.exe flashdmp.bin: -r16 rawconfig.bin 3de 2

Then inject them into the donor NAND renamed "7371.bin" with the following
commands:

nandpro.exe 7371.bin: -w16 rawkv.bin 1 1

nandpro.exe 7371.bin: -w16 rawconfig.bin 3de 2

Open the orig.bin in 360 flash tool using your CPU key to make sure all the info looks correct.

Use the rebuilt NAND to make freeboot image.

Xenon NAND: [ Register or Signin to view external links. ]

Falcon NAND: [ Register or Signin to view external links. ] <- has 1 bad block



If anyone would mind donating a Nands with the dashboard kernel of 7371 preferably banned it would be helping other people out aswell =]

I have the Falcon and Xenon Nand’s already. But still need a Zephyr, Jasper 16, Jasper 256, and Jasper 512.

If you can donate, I will give you credit (: - also if you do have any to donate PM me or Post in this thread.

---

TTG_Dean0's How To Recover From A Bad Nand Flash (Dead 360)

Click to View Content

Hey Guys

Ok if you have tried the jtag hack and have been unsucessfull (Xbox wont turn on at all and "Cannot detect a flash controller" in Nandpro) do not panic there is salvation. ;)

You can recover from this Hell by shorting out the nand there is two methods on how to do this and both accomplish the same thing. The first method is the one that is most recomended but is a bit more difficult to do. what you want to do is short out pins 44 and 47 by connecting them with a piece of wire (or anything conductive ex: screwdriver or pin)


METHOD 1

SHORTING OUT PINS 44-47

Here is a detailed diagram I have made showing the pin outs on the nand so you know which pins you need to connect together to short it out.

[ Register or Signin to view external links. ]
The procedure for causing the short is the same for both methods and will be reviewed below

NOW THE SECOND METHOD IS A LOT EASIER BUT IS ALSO MUCH MORE LIKELY TO CAUSE DAMAGE TO YOUR 360. USE AT OWN RISK!!!!!
This method involves getting a piece of stripped wire and laying it across all of the legs of the nand at once. Thus causing a short and forcing the nand into a recovery mode where you can than erase or rewrite it. below is another pic i have edited to show you what i did.
[ Register or Signin to view external links. ]
*Note the wire can be held in place with your index finger on one side and your middle finger on the other while doing the procedure.


PROCEDURE

This procedure works for both methods but i am going to demonstrate Method 2 because it is easier to execute and illistrate

Disconnect all cables from your console. Reconnect the video cable and get your wire in place on the nand.

Pic Below

[ Register or Signin to view external links. ]

Now while still holding the wire in place with your finger reconnect the power cable to the board

This is what everything should look like

[ Register or Signin to view external links. ]

Now remove the wire carefully not to touch anything on the board. (best method is to just let go of it and pick it up after.) check your xbox 360's power bar if the light has stayed orange than you should be fine if it turned red than the surge protect has kicked in and you need to repeat the procedure.

Now open the command prompt and go into nandpro and test reading from the nand.

ex: C:nandpronandpro lpt: -r16 test.bin 1 1

this command will attempt to dump your keyvault if you get a flash config and it succeeds than your nand is able to read and write again.

* At this point i would suggest erasing the nand (ONLY DO THIS IF YOU HAVE PROPER BACKUPS OF YOUR NAND)

To erase the nand go in to the nandpro directory ex: C:Nandpro and type type: nandpro lpt: -e16 0 400

This will completly erase the nand than just flash your original back or the proper version of XBR (If you flash your original back you must remove the jtag wires or the console will not boot)

Your Xbox 360 should now be alive once again.!!

I do not take credit for this, thought id post it though

here is original: [ Register or Signin to view external links. ]

Thanks
dean

P.s. Thank if liked and if sum1 would like to take watermark outta pics forme it'd be great

thanks

---

Hola's: [TUT] How To Install Any Game's ISO To Your Jtag [TUT]

original post: Forums/viewtopic/t=253614.html

Ask questions on the original post.

Click to View Content

How To Install ISO To Your Jtag

EDIT: THANKZ Dark for the sticky again

Things You Will NEED!

Jtag
Hardrive
XeX Menu Download
[ Register or Signin to view external links. ]
Xport 360 Download
[ Register or Signin to view external links. ]
Some Games
If you dont have the game or a working dvd drive
[ Register or Signin to view external links. ]
Wx360 For if you dont have the disk or Working DVD Drive
[ Register or Signin to view external links. ]
Transfer Cable

Ok so Lets Get Started!!

Step 1
First you need to Download Xport 360 and XeX Menu. Once you get xex menu on your Desktop open it up and there should be a Folder called CODE999. After you got those downloaded, open up you hardrive using your transfer cable in Xport 360 and go to Partition 3, COntent, Then The 000000 folder. Then get Code999, that is in the xex menu folder, And Drag it into the 00000 Folder. Thatz all you have to do on The Computer.

Step 2
Then put your Hardrive into your Jtag and boot up your Jtag. Then go to game library, and you should see XeX Menu 1.1 in your Recent Games. CLick XeX Menu 1.1 and hit start Game.

Step 3
Then once your in XeX Menu hit RB the click Content, 000000, then hit y and select Create New Folder and Make the Folder Games. THen Click the Games Folder and hit y and select Create Folder. Then Name the FOlder to wat ever Game's ISO That you want

Step 4
[spoil]Once you Have your folders created go into the Game Folder that You Want to get the ISO FOR. Once your in the folder hit y then select Install DVD. After you hit that you should see 2 bars and it should start loading. This usually takes about 30 minutes to an hour.

Step 5
TO make sure it worked, Turn off your Jtag. Then turn it back on, go to Game Library, XeX Menu, hit RB so it will Take you to your Hardrive, Then hit partition 3, Content, 000000 Folder, hit games, Then select Wat ever Game's ISO That you made and click the Folder. IF you followed all of These Steps it Should Work.If You see all the files in the folder Than Congratulations!!! You succesfully added ISO To your Jtag!! 8)

If you dont have the game or a working DVD Drive then Follow this

Download the iso using the link i gave you 360 isos, then once you have it downloaded open it up in Wx360. Once you do that create a Folder named the Game you want to do. Then on Wx360 and hit file, extract all, and extract all the files into that FOlder. In Wx360 you know when its doen extracting because next to the files it should say done going down the whole lis.Once thats done, just drag the Folder into the 00000 FOlder. There you go.

IF You need any Help then you can PM Me or COntact me on Aim. I am always here to Help
My Aim: baseballlife96

I take full Credit For this tutorial. I did not copy and Paste anything for this tutorial. This Was Made by me and no one else.

If you think this TUT could be improved Reply Below or PM Me and i would be glad to update it.

If this helped, It is polite to Hit the Thank you Button

---

Mw2 System Link Tutorial

This tutorial is by the TTG user - Hola.

The original post is here: Forums/viewtopic/t=250763.html

Feel free to ask questions on the ORIGINAL POST

Click to View Content

THINGS YOU WILL NEED

Retail Xbox
Jtagged Xbox
2 ethernet cables or two wireless adaptors
Mw2 Installed onto your Hardrive
A patch

STEP 1.Ok First thing you will need to do is install mw2 to your hardrive. I am not going to go into detail because there are many tuts that tell you how to do that

Step 2.Then connect your Jtagged xbox's internet to the same router that your Retail xbox is connected to

Step 3.Then on your Jtag load up Mw2. It should bring you to the multiplayer menu. THen go to system link. Then hit create match and then turn xbox live unlocks on. And start the match.

Step 4.On your Retail xbox sign into the account that you want to mod

Step 5.THen load up mw2 on your retail xbox and go to the multiplayer menu and hit system link, then hit find match. You should see the match that you just started on your Jtag. Then Join the Match.

If you got all that to work than congratulationz, you succesfully made a system link lobby!!!!

This tutorial was completely made by me. I did not copy and paste anything for this tutorial.

If you need any help you can pm me or contact me on aim
My Aim: baseballlife96

If i helped + rep would be appreciated. Thankz
If you guys think i need to improve my TUT then just reply below or PM Me
It's polite to hit the thank you button

---

How to Get CPU + DvD Key On Jtag Xbox 360!

Tutorial by User - M40snipes

Original Thread: Forums/viewtopic/p=1824746.html#1824746

Any questions post on the ORIGINAL THREAD.

Click to View Content

How To Get CPU Key
First What You Going To Do Is Turn Off Ur Jtag And Follow The Steps Below

1. With Ur Jtag Off Click The Eject Button
2. It Will Boot Into Xell.
3. When It Says Fuse 1 , Fuse 2 , ETC Take A Picture Of The Fuse Sets With a Camara Or Webcam
4. After You Have Did This Add Fuse Set 3 And Fuse Set 5 Together ( Or 4 And 6 )
5. Add Fuse Sets Together Like This
Fuse Set 3 : 12345
Fuse Set 5 : 67890
CPU : 1234567890
6. Copy You CPU And Paste in Notepad To Save For Later

I Hope This Helps All Of You Guys / Girls Out there With This Problem Please Thank My Topic.

How To Get DvD Key
Follow the Steps Bellow To Get Ur DvD Key On Ur Jtag!

1. Boot Up Ur Jtag And Go To XeX Menu 1.1
2. Go To Flash360 Run It Hit ( X ) To Back Up Current Nand
3. Now Its On ur USB Go To The Computer And Start Up Flash360 Tool
4. Enter Ur CPU ( If u dont have it folow the steps above ) And the program will restart
5. Now Click the .... And Open Ur flashdmp.bin Thats On Ur USB
5. Then It Will say DvD Key And DvD OSIG Copy Both Of These And Paste In Notepad And Save For Later =)

---

Get Original Nand from XBR/Freeboot Image

Tutorial by TTG user - daz_gregory

Original Post: Forums/viewtopic/t=256387.html

Any Questions post them on the ORIGINAL POST.

Click to View Content

This tutorial requires you to use the program nandpro. I'm not going to show you how to set that up so google is your friend.

Requirements:
- Nandpro: (Google Is Your Friend For This)

-XBR/Freeboot Image of Your JTAG
-Nand Dump of Corresponding Motherboard (7371 or less)

-Xenon: [ Register or Signin to view external links. ]

-Zephyr:(if you have a Zephyr nand dump PM me)

-Opus:(if you have an opus nand dump pm me)

-Falcon: [ Register or Signin to view external links. ]

-Jasper(if you have a jasper nand dump pm me)




Place both your xbr/freeboot image and good nand dump into the same directory as nandpro.

Once that's done, run the following commands (with your corresponding file names):

nandpro xbr-freeboot.bin: -r16 rawkv.bin 1 1

[ Register or Signin to view external links. ]

nandpro xbr-freeboot.bin: -r16 rawconfig.bin 3de 2

[ Register or Signin to view external links. ]

nandpro goodnand.bin: -w16 rawkv.bin 1 1

[ Register or Signin to view external links. ]

nandpro goodnand.bin: -w16 rawconfig.bin 3de 2

[ Register or Signin to view external links. ]

Now you have your original nand.

---

How To Install Xellous

Tutorial by TTG user - TTG_Mitchell

Ask questions on this topic.

Click to View Content

How To Install Xell


Xell is used to grab your CPU Key for your console. Which is a good thing to have in case you need to open your KV. Install Xell is easy and takes little to now time.

Download the image for your motherboard revision. Extract and place it in the nandpro folder. Make it easy on yourself and rename the Xell file to Xell

With your LPT cable and everything still set up. You will be using nandpro again. So here we go again.

1. Click start
2. Click run
3. Type CMD
4. Type the command.

Code:
C:Nandpro20bnandpro.exe lpt: -w16 Xell.bin


Don't worry about the file size. It is meant to only write to the beginning of your NAND flash.
5. Click enter and it should starting writing.
6. Once it is done writing. Unplug the lpt cable from the PC and turn on the 360. It should boot into a blue screen. If it does then you did it right.

Getting the CPU key.

Have a camera ready to take a picture of the Fuse Set's that pop up briefly.
Take a picture that includes fuse set 3,4,5,and 6. These contain your CPU key.

Take either 3 and 5 or 4 and 6. This will make up your cpu key. 3=4 5=6 So for example. I will take 3 and 5.
3= E42D681ED06A6D1C
5= 1FFD8E48C56A2058

So my CPU Key is - E42D681ED06A6D1C1FFD8E48C56A2058

Adding either one of the two will make your CPU key.

After getting your cpu key you can write your original nand image back to the board. Or go straight forward and install XBReboot or freeBOOT.

To flash your nand image back on, use this command
Code:
C:NandPro20bnandpro.exe lpt: -w16 (name of your nand backup)

---

How to tell if a KV is good or BAD

Original TTG poster - fertz

Original Post: Forums/viewtopic/t=251314.html

ASK QUESTIONS ON THE ORIGINAL POST

Click to View Content

How to tell if a kv is real or will give you Christmas lights or rrod.

This is 5 easy steps that take less than a minute to find out if it is fake.



Need help putting a kv into your jtag check this tutorial

Forums/viewtopic/t=211503.html


1.First off make sure the kv is along the lines of Kv_dec.bin it can be diffrent but as long as it has .bin at the end its ok. Also if it is 16.0KB

[ Register or Signin to view external links. ]

2.Once you have your kv open it up in Your favorite Hex Editor i am using Hxd

[ Register or Signin to view external links. ]

3.Once opened make sure there is 7 lines that are empty in the very beginning if it dosent have this right off the bat it is fake.

[ Register or Signin to view external links. ]

4. Make sure there is a large space in the kv it should separate two paragraphs

[ Register or Signin to view external links. ]

[ Register or Signin to view external links. ]

5.Make sure at the end it says Signature Cerification and certificatecollection at the end and there is a space at the very end with no writing at the bottom after the space.

[ Register or Signin to view external links. ]

Vouches

[spoil]

HazeyyxD wrote Good post gonna try next time thanksss.<3

TTG-LegitTrack wrote this helped me alot put this topic on sticked man thank you!!!!!!!!!!!!!!!!!!!!!!!

RusH_HD_Shox wrote definatly should be stickied

BoXMan wrote This is very helpful and should be stickied

xtoreload110 wrote Gooood Post Man Keeep It UP!

bean10thlobby wrote Nice post man 20 chara

Classic wrote Should be stickied.

BBmodz wrote I think i see maybe a new sticky
-BBmodz

jhoward wrote thanks man. u helped meh.

TTG_RME7 wrote Should be stickied....

TTGTalented wrote Wow this'll help so much Thanks

xcubanXphantomx wrote nice post really helps stop scammers