Try using this nand-x wire setup and let me know what if it has a successful dump.

[ Register or Signin to view external links. ]

Troy20202020 wrote Everyone who has commented:

Nand-x is on v3

No I didn't turn on the Xbox while the Nand-x was in.

Yes I have tested my Nand-x on another console, Perfect read.




I really don't know what to do with this :-/

I can see from here, your point is in the hole, just not touching the side. re-solder it, but if worst comes to worst, message me I can make you a dummy nand to write it.

Right, I remapped the bad blocks, Even though there was only 1 at 3E, But its not after block 250 (Writing a nand with a bad block after 250 is ok, Not really recommended though) So i created Xell Reloaded ("falcon_hack_aud_clamp.bin") I have done the alternate points, Q2N1, and DVD_Open_Trey, That is aud_clamp wiring, right? I just thought id do that instead of DB1F1.

Anyway, I wrote Xell, And everytime i get a bad block at 3E? Why? I have re-soldered my nand-x multiple times but its always 3E.

Heres what i get:

Flash Config: 0x01198010
Writing Nand
falcon_hack_aud_clamp.bin
Error: 202 writing block 3E
Done!
in 0:10 min:sec

Now i get E79 and i cant write the original nand back because ill get a bad block at 3E!!

FFS!!

Troy20202020 wrote Right, I remapped the bad blocks, Even though there was only 1 at 3E, But its not after block 250 (Writing a nand with a bad block after 250 is ok, Not really recommended though) So i created Xell Reloaded ("falcon_hack_aud_clamp.bin") I have done the alternate points, Q2N1, and DVD_Open_Trey, That is aud_clamp wiring, right? I just thought id do that instead of DB1F1.

Anyway, I wrote Xell, And everytime i get a bad block at 3E? Why? I have re-soldered my nand-x multiple times but its always 3E.

Heres what i get:

Flash Config: 0x01198010
Writing Nand
falcon_hack_aud_clamp.bin
Error: 202 writing block 3E
Done!
in 0:10 min:sec

Now i get E79 and i cant write the original nand back because ill get a bad block at 3E!!

FFS!!

J-runner doesn't allow you to do AUD_CLAMP TRAY_OPEN, only AUD_CLAMP so wire DB1f1 up and she should boot

IVIoNoXiDe wrote

Troy20202020 wrote Right, I remapped the bad blocks, Even though there was only 1 at 3E, But its not after block 250 (Writing a nand with a bad block after 250 is ok, Not really recommended though) So i created Xell Reloaded ("falcon_hack_aud_clamp.bin") I have done the alternate points, Q2N1, and DVD_Open_Trey, That is aud_clamp wiring, right? I just thought id do that instead of DB1F1.

Anyway, I wrote Xell, And everytime i get a bad block at 3E? Why? I have re-soldered my nand-x multiple times but its always 3E.

Heres what i get:

Flash Config: 0x01198010
Writing Nand
falcon_hack_aud_clamp.bin
Error: 202 writing block 3E
Done!
in 0:10 min:sec

Now i get E79 and i cant write the original nand back because ill get a bad block at 3E!!

FFS!!

J-runner doesn't allow you to do AUD_CLAMP TRAY_OPEN, only AUD_CLAMP so wire DB1f1 up and she should boot

Okay will do mate and ill let you know how it goes, If it doesn't work its getting thrown off my balcony ;)

Monoxide,,,,, I am your new fanboy :trollin: <3