You are viewing our Forum Archives. To view or take place in current topics click here.
Coolrunner and DemoN RGH Help
Posted:

Coolrunner and DemoN RGH HelpPosted:

TTG_NightMareModz
  • Challenger
Status: Offline
Joined: May 02, 201113Year Member
Posts: 189
Reputation Power: 8
Status: Offline
Joined: May 02, 201113Year Member
Posts: 189
Reputation Power: 8
I have a zephyr motherboard on dash 12625,I bought a cr3 and a DemoN. I went ahead and redid all the points connecting the DemoN to the motherboard, and cleaned up all the flux. I plugged in the micro usb cable to the demon, switched it to PRO, and opened up demon toolbox. Demon toolbox will let me turn the console on and off without touching the power button so I must have somthing right or demon tools wouldnt be able to turn my system on and off correct? But when I open jrunner, it still tells me device not found!? Am I missing somthing or what? I just want to be able to read this nand already!
#2. Posted:
Garbotron
  • Rising Star
Status: Offline
Joined: Jul 02, 201212Year Member
Posts: 753
Reputation Power: 34
Status: Offline
Joined: Jul 02, 201212Year Member
Posts: 753
Reputation Power: 34
Did you install the usb driver plugins??? Does the demon show up under devices??? Can you switch nands with the demon tool box or just power only???
#3. Posted:
HarmfulMushroom
  • TTG Contender
Status: Offline
Joined: Aug 01, 201014Year Member
Posts: 3,245
Reputation Power: 148
Status: Offline
Joined: Aug 01, 201014Year Member
Posts: 3,245
Reputation Power: 148
Oh boy, Zephyrs are a bitch to glitch.. I gave up on mine personally. But as the guy above me posted, make sure you have the correct drivers installed. I had that problem myself a little while ago, couldn't figure out what I did wrong..

If you still need help, PM me and I'll see what I can do.
#4. Posted:
5KMods
  • TTG Undisputed
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
You obviously dont understand.

Why would you install a demon to a Zephyr withOUT getting it gltiching first - bad boots if it boots at all.

You need to be on 14719/RGH2.0 - dual boot with XBL(Stock nand).

anything below 14717 still has a single stage CB, if you try updating it after you gltich it you'll install Split CB's, and will need to Do RGH2.0.
#5. Posted:
OpticGumpii
  • New Member
Status: Offline
Joined: Dec 06, 201212Year Member
Posts: 2
Reputation Power: 0
Status: Offline
Joined: Dec 06, 201212Year Member
Posts: 2
Reputation Power: 0
ok sorry for asking, but i have my slim trinity RGH console. i've used it for about a year, can i just install the demon or do i have to do something to my coolrunner again?
#6. Posted:
5KMods
  • TTG Undisputed
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201014Year Member
Posts: 5,070
Reputation Power: 216
OpticGumpii wrote ok sorry for asking, but i have my slim trinity RGH console. i've used it for about a year, can i just install the demon or do i have to do something to my coolrunner again?


Dont thread-Hyjack make a new topic for your problem.

It depends on the chip your using.
Jump to:
You are viewing our Forum Archives. To view or take place in current topics click here.