PC SupportOverheating Problem
Posted:

PC SupportOverheating ProblemPosted:

Pingers
  • Gold Member
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Motto: Drug Lord
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
I recently switched from intel to ryzen, and after installing my new cpu ect, my cpu is getting to around 90+ degrees and restarting itself?

I've reapplied new paste and made sure all cables are in correctly and it's still overheating!

Any suggestions?

Got a gigabyte b450 m board with ryzen 5 3600
#2. Posted:
Adam
  • Wizard
Status: Offline
Joined: Dec 10, 201112Year Member
Posts: 6,077
Reputation Power: 30932
Motto: :Salt:
Motto: :Salt:
Status: Offline
Joined: Dec 10, 201112Year Member
Posts: 6,077
Reputation Power: 30932
Motto: :Salt:
What CPU cooler you got?

When it gets a bit hot, are you checking to make sure the fan spins OK?

If in doubt, take the cooler off and check to see what pattern the thermal paste gives you. Could be a bad mount to the board.
#3. Posted:
Pingers
  • Blind Gifter
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Motto: Drug Lord
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Adam wrote What CPU cooler you got?

When it gets a bit hot, are you checking to make sure the fan spins OK?

If in doubt, take the cooler off and check to see what pattern the thermal paste gives you. Could be a bad mount to the board.


Ryzen 5 stock cooler and yeah fans spinning perfectly and checked earlier and paste is fine
#4. Posted:
Quarantine_Clean
  • Winter 2020
Status: Offline
Joined: Dec 02, 20203Year Member
Posts: 387
Reputation Power: 3040
Status: Offline
Joined: Dec 02, 20203Year Member
Posts: 387
Reputation Power: 3040
Only thing I can think of if it isn't a defective CPU is thermal paste (which you have re-applied already) and just maybe the mount isn't tight enough for it to make contact between cooler and CPU...




Is it a brand new CPU?
#5. Posted:
Forest
  • Summer 2020
Status: Offline
Joined: Jul 13, 200915Year Member
Posts: 7,815
Reputation Power: 3052
Status: Offline
Joined: Jul 13, 200915Year Member
Posts: 7,815
Reputation Power: 3052
Did you make sure to remove the plastic piece on the bottom of the heat sink before applying thermal paste? I've seen Dell forget to do that at the factory causing temps to sit at 90+ at idle

Did you use the correct mounting holes for the CPU cooler? Wonder if it's not tight enough, and not making adequate pressure. Also are you running stock, or have you done any type of overclocking so far?


Worse comes to worse, you might have a bed temp sensor which could be false reporting the temperatures. If it's a new processor, you should be able to start the RMA process for this.
#6. Posted:
Pingers
  • Winter 2022
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Motto: Drug Lord
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Quarantine_Clean wrote Only thing I can think of if it isn't a defective CPU is thermal paste (which you have re-applied already) and just maybe the mount isn't tight enough for it to make contact between cooler and CPU...




Is it a brand new CPU?


Yeah it's a brand new one
#7. Posted:
Pingers
  • Winter 2023
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Motto: Drug Lord
Status: Offline
Joined: Oct 08, 201311Year Member
Posts: 3,136
Reputation Power: 8031
Motto: Drug Lord
Forest wrote Did you make sure to remove the plastic piece on the bottom of the heat sink before applying thermal paste? I've seen Dell forget to do that at the factory causing temps to sit at 90+ at idle

Did you use the correct mounting holes for the CPU cooler? Wonder if it's not tight enough, and not making adequate pressure. Also are you running stock, or have you done any type of overclocking so far?


Worse comes to worse, you might have a bed temp sensor which could be false reporting the temperatures. If it's a new processor, you should be able to start the RMA process for this.


There was no plastic there and done the screws till they clicked and how do I start the process?
#8. Posted:
r00t
  • Administrator
Status: Offline
Joined: May 18, 201113Year Member
Posts: 16,414
Reputation Power: 24459
Status: Offline
Joined: May 18, 201113Year Member
Posts: 16,414
Reputation Power: 24459
Pingers wrote
Forest wrote Did you make sure to remove the plastic piece on the bottom of the heat sink before applying thermal paste? I've seen Dell forget to do that at the factory causing temps to sit at 90+ at idle

Did you use the correct mounting holes for the CPU cooler? Wonder if it's not tight enough, and not making adequate pressure. Also are you running stock, or have you done any type of overclocking so far?


Worse comes to worse, you might have a bed temp sensor which could be false reporting the temperatures. If it's a new processor, you should be able to start the RMA process for this.


There was no plastic there and done the screws till they clicked and how do I start the process?

You probably need to tighten the screws. The springs will protest a little and stop turning once completely fastened.
#9. Posted:
Runts
  • Runescape
Status: Online
Joined: Apr 23, 201113Year Member
Posts: 17,885
Reputation Power: 18381
Motto: JOKES UP !
Motto: JOKES UP !
Status: Online
Joined: Apr 23, 201113Year Member
Posts: 17,885
Reputation Power: 18381
Motto: JOKES UP !
make sure everything is cleaned to. when mine cakes up it can get hott
Users browsing this topic: None
Jump to:


RECENT POSTS

HOT TOPICS