Tutorials Navigation
How To Make A Modded Controller
Tutorial Name: How To Make A Modded Controller
Category: Xbox 360 Tutorials
Submitted By: Transit
Date Added:
Comments: 6
Views: 10,730
Related Forum: Xbox Forum
Share:
Requirements:
A TT9 Torx Driver (TT8 may fit better, I only had a TT9)
A Small Push Button Switch
Some Thin Wire, Such as IDE Cable
An Xbox 360 Controller (Wired or Wireless, it works the same)
Soldering Equipment
A Drill and Drill bit (To match the diameter of the thread on your switch)
Some form of surface to work on.
A TT9 Torx Driver (TT8 may fit better, I only had a TT9)
A Small Push Button Switch
Some Thin Wire, Such as IDE Cable
An Xbox 360 Controller (Wired or Wireless, it works the same)
Soldering Equipment
A Drill and Drill bit (To match the diameter of the thread on your switch)
Some form of surface to work on.
STEP.2
Taking the battery out unlocks a BONUS SCREW !
There are 7 screws to remove, so grab that Torx driver and twist! (Anti -Clock-wise)
With the buttons facing DOWN , separate the two halves carefully, paying attention to the motors.
Taking the battery out unlocks a BONUS SCREW !
There are 7 screws to remove, so grab that Torx driver and twist! (Anti -Clock-wise)
With the buttons facing DOWN , separate the two halves carefully, paying attention to the motors.
STEP.3
Find the best place to put your switch, choose very carefully, as once you've drilled, its staying on your $50 Controller!
Once you have found the right place, place the two halves back together and see if there is enough room for your switch to go in.
If there is, well done. Remove the board so that it doesn't get damaged, then put the bit in your drill and ~~deface~~ improve $50 worth of electronics.
Find the best place to put your switch, choose very carefully, as once you've drilled, its staying on your $50 Controller!
Once you have found the right place, place the two halves back together and see if there is enough room for your switch to go in.
If there is, well done. Remove the board so that it doesn't get damaged, then put the bit in your drill and ~~deface~~ improve $50 worth of electronics.
step 4:
Put the switch in your new hole. Make sure that you orient the pins so that they are not getting bent or squashed when the controller is back together. I had to remove some of the motor holder to fit my switch in.
Put the switch in your new hole. Make sure that you orient the pins so that they are not getting bent or squashed when the controller is back together. I had to remove some of the motor holder to fit my switch in.
Step.5
Fire up the soldering iron, not too hot or else it might break some components.
Point one and two are in pictures 2 and 3 respectively.
An final overview is in picture 4.
5 and 6 show the switch.
7 shows what happens when your iron is too hot and you take too long to make a joint.
Make sure wiring runs stay clear of the black button pads, analogue stick movement and screw holes.
Fire up the soldering iron, not too hot or else it might break some components.
Point one and two are in pictures 2 and 3 respectively.
An final overview is in picture 4.
5 and 6 show the switch.
7 shows what happens when your iron is too hot and you take too long to make a joint.
Make sure wiring runs stay clear of the black button pads, analogue stick movement and screw holes.
Step.6
Are the switch pins going to make contact with anything on the other half of the controller when reassembled?
Are all of the wires free from places of movement or screw holes?
Are the solder joints correct and not dry?
Are all of the annoying black pieces of the controller back on their positioning pins?
(they are annoying as they have a habit of coming off the pins half way through putting it back together)
Has your soldering iron made suitably sized black marks on your window ledge?
Four out of five is good enough to continue.
For a quick test, replace the battery and depress your switch all the way. If the player one led lights up very dimly, then the mod worked!
Now try putting it back together without breaking anything.
Are the switch pins going to make contact with anything on the other half of the controller when reassembled?
Are all of the wires free from places of movement or screw holes?
Are the solder joints correct and not dry?
Are all of the annoying black pieces of the controller back on their positioning pins?
(they are annoying as they have a habit of coming off the pins half way through putting it back together)
Has your soldering iron made suitably sized black marks on your window ledge?
Four out of five is good enough to continue.
For a quick test, replace the battery and depress your switch all the way. If the player one led lights up very dimly, then the mod worked!
Now try putting it back together without breaking anything.
Step.7
If you are having trouble putting it all back together, try wigging it while applying gentle force, and make sure all wires and button rubbers are not obstructing anything.
If you are having trouble putting it all back together, try wigging it while applying gentle force, and make sure all wires and button rubbers are not obstructing anything.
Credit:
[ Register or Signin to view external links. ]
Ratings
Comments
ScrutPosted:
TotallyWack seems abit pain staking then if you fu_ck up theres 25 gone down the drain.. people with less exp should just go buy 1 and it wont break.. and at least you can return it if its broken!
I understand what you mean but many people like the idea of making (modding) it them self.
TotallyWackPosted:
seems abit pain staking then if you fu_ck up theres 25 gone down the drain.. people with less exp should just go buy 1 and it wont break.. and at least you can return it if its broken!
_XeNoX_Posted:
this is not got but i dont work with the new CG board and with the CG2 board buy a XMOD chip on
eay 20$ an 20 mode with jitter etc :)
jitter= auto m16 +famas have fun to buy this i got it too
eay 20$ an 20 mode with jitter etc :)
jitter= auto m16 +famas have fun to buy this i got it too
Related Tutorials
- 01. How to remove family settings/parental controls on Xbox 360(4,220)
- 02. Pico Flasher ISD / Sonus Programming(3,631)
- 03. College Football Revamped Tutorial/Installation(7,203)
- 04. (JTAG/RGH) How-To Download, Extract & Play Goldeneye 007(7,331)
- 05. Darkest of Days Achievement Guide [XBOX 360](2,980)
- 06. College Hoops 2K6 Achievement Guide [XBOX 360](3,264)
- 07. Blazing Angels Achievement Guide [XBOX 360](3,275)
- 08. Avatar: The Burning Earth Achievement Guide(3,814)
- 09. 2006 FIFA World Cup Achievement Guide [XBOX 360](4,716)
- 10. Turok: Sniper!(2,510)
- 11. Turok: Impaler Ribbon(2,355)
- 12. Turok: Dino Dominance(2,395)
- 13. 0 Day Attack on Earth Achievements Guide(3,111)
- 14. Turok: Sell Your Shotguns(2,556)
- 15. Terminator: Salvation Achievement Guide(3,050)
"How To Make A Modded Controller" :: Login/Create an Account :: 6 comments